MEM30032A Produce Basic Engineering Drawings

Question Assessment:

Q-1 What is the type of drawing?

Q-2 The number of folding methods for folding of various sizes of drawing sheets is __________
A. 1
B. 2
C. 3 D. 4

Q-3 Define engineering drawing. Why is drawing called universal language of engineers?

Q-4 What is layout of drawing sheet?

Q-5 List out the contents of title block and material list

Q-6 Where and why a cutting plane is drawn in a drawing?

Q-7 What is the importance of dimensioning?

Q-8 What is dimensioning?

Q-9 What are the general rules of dimensioning?

Q-10 What are the main uses of scale?

Q-11 What is a sectional view? Why sectional views are used in drawing?

Q-12 What is section or hatching lines?

Q-13 What is an isometric view?

We'll write Task tailored to your instructions.
Upto 30% OFF on your Task

Order Now Whatsapp Now

Q-14 The ratio of height to length of an arrow in dimensioning is ___

A) 1:2
B) 1:3
C) 1:4
D) 1:1.5

Q-15 Which type of dimensioning is shown in the figure?

A) Parallel dimension
B) Unidirectional dimension
C) Combined dimension
D) Chain Dimension

Q-16 Which type of dimensioning is shown below?

A) Chain dimension
B) Parallel dimension
C) Unidirectional dimension
D) Combined dimension

Q-17 Which type of dimensioning is done below?

A) Unidirectional and chain dimension
B) Aligned and parallel dimension
C) Aligned and chain dimension
D) Unidirectional and parallel dimension

Q-18 Identify the type of dimensioning used in the figure below.

A) Parallel and aligned dimension
B) Parallel and unidirectional dimension
C) Chain and aligned dimension
D) Chain and unidirectional dimension

Q-19 Which type of dimensioning is done in the example below?

A) Parallel dimension
B) Chain dimension
C) Combined dimension
D) Aligned dimension

Q-20 Identify the type and system of dimensioning in the example given below.

A) Unidirectional and parallel dimension
B) Unidirectional and chain dimension
C) Unidirectional and combined dimension
D) Aligned and combined dimension

Q-21 Dimension lines should not intersect each other as far as possible.
True OR False

Q-22 Identify the ‘a’ in the below given picture.

A) dimension line
B) outline
C) leader
D) extension line

Q-23 While representing the diameter in dimensioning it is represented as
A) D
B) Ø
C) Dia
D) d

Q-24 From below given figure, match the following.

A) a, i; b, ii; d, iii; e, iv
B) a, iv; b, iii; d, ii; e, i
C) a, i; b, iv; d, iii; e, ii
D) a, iii; b, ii; d, i; e, iv

Q-25 In engineering drawing, which type of arrowhead is used?
A) Open (90˚)
B) Small open circle
C) Closed and filled
D) Oblique stroke

Q-26 Representative fraction is the ____________________
A) ratio of the length in drawing to the actual length
B) ratio of the actual length to the length in drawing
C) reciprocal of actual length
D) square of the length in drawing

Q-27 The length of the drawing is 20 cm, the scale is given as 2:1. Find the actual length.

Q-28 The actual length is 1cm. The length of drawing is 30 cm. Find the representative factor

Q-29 What is the difference between first and third angle projection?

Q-30 What is dimensional tolerance?

Q-31 What is the difference between unilateral and bilateral tolerance?

Q-32 What is geometric dimensioning?

Q-33 What are the benefits of GD &T?

Q-34 List down the symbol of the form, profile, orientation, location, and runout.

Q-35 Elaborate feature control frame shown in figure.

Q-36 Describe the procedure for the compliance check of the drawing according to the work requirements and specifications.